Residential · The Villages, FL
Peeling, hot-tire pickup, and bubbled coatings usually mean the fix is epoxy removal, not another topcoat. Elite Epoxy The Villages removes failed epoxy and installs a new industrial-grade system with proper profiling and moisture control in The Villages.
Prep starts with a site check for coating thickness, bond failure, contamination (oil, silicone, tire plasticizers), and cracks or spalls. We isolate the work area, protect walls and door tracks, and set up HEPA dust control, then strip coatings with diamond grinding (16-30 grit) or shot blasting to achieve a consistent concrete surface profile (CSP 2-3 for most epoxy, higher CSP for heavy build). After removal, we detail edges with hand grinders, clean with industrial vacuums, repair joints and chips with epoxy mortar, and verify the slab is ready before any primer goes down.
Central Florida slabs often deal with humidity swings and moisture vapor transmission, so we test and plan for it before we recoat. Where needed, we apply a moisture-mitigating epoxy primer and then build the system for the space, 100% solids epoxy for garages and shops, urethane cement for hot, wet service areas, and UV-stable polyaspartic or polyurethane topcoats where sunlight hits. You choose the finish, solid color, decorative vinyl flake, quartz, or metallic epoxy, plus the right texture from smooth to slip-resistant with aluminum oxide or silica broadcast.
The Villages customers choose us because epoxy removal is messy, technical work and we do it the right way, not the fast way. We focus on mechanical removal, not acid etching, and we document surface profile, repairs, and coat build so the new system has a reliable bond. Our crews are licensed and insured, show up with commercial grinders, shot blasters, and dust containment, and we write clear scopes that specify primers, topcoats, and cure times so you know exactly what is being installed.
After recoating, we walk the floor with you and confirm coverage, slip resistance, and clean lines at walls and transitions. You get a written estimate up front, a defined prep plan, and a floor system selected for your use, vehicle traffic, chemicals, and cleaning routine. We also leave simple care instructions, recommended cure windows for foot traffic and vehicles, and guidance on mats, jack stands, and hot-tire exposure so the new coating stays tight for the long term.
We install solid-color epoxy, full and partial decorative flake broadcasts, quartz systems, and metallic epoxy, typically finished with a clear polyaspartic or polyurethane topcoat for added wear and UV stability.
Yes. We route and fill cracks, patch spalls, and level minor surface issues with epoxy repair materials before the base coat, then blend repairs so the finished floor looks uniform.
Coatings cover most discoloration once the slab is properly cleaned and prepped, and the topcoat helps resist tire staining and chemicals. Severe oil saturation may require deeper cleaning and localized treatment before coating.
Yes. We can broadcast traction media into the clear coat or adjust the build and texture depending on the area, such as garages, lanais, patios, and commercial entries.
Warranty terms depend on the coating system and site conditions, including moisture and substrate integrity. We’ll outline what is covered in the written estimate before you approve the work.
If your garage or commercial floor is peeling, blistering, or wearing through, epoxy removal is often the only way to get back to a durable, good-looking surface. Coatings fail for predictable reasons: poor surface prep, moisture vapor coming through the slab, incompatible products stacked on top of each other, or contamination from oil and tire plasticizers. Elite Epoxy The Villages removes failed coatings with mechanical profiling and then installs a new epoxy or polyaspartic system designed for your traffic, cleaning needs, and exposure to sun and humidity.
We start by identifying what is on the slab, the thickness, and why it let go. Then we remove coatings down to clean concrete using planetary grinders with metal-bond diamonds, edge tools for tight areas, and HEPA dust collection for cleaner work. Once the old epoxy is gone, we repair defects and build a coating system with the right profile and chemistry, 100% solids epoxy for most residential garages, and options like polyaspartic topcoats for faster return to service and better UV stability.
For properties in The Villages, moisture and humidity matter as much as the product choice. When the slab needs it, we use moisture-mitigating primers and avoid shortcuts that lead to bubbles and delamination later. You can choose a simple solid-color epoxy, a full broadcast vinyl flake floor, quartz for extra traction, or metallic epoxy for showpiece areas, all finished with a wear-resistant clear coat.
The result is a floor that looks consistent, cleans easily, and is built to handle the real causes of failure, not just the symptoms. If you want epoxy removal and a properly specified recoat, we will inspect the slab, explain the prep plan, and provide a free written estimate with materials, steps, and timelines.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in The Villages. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
